Search results

Evening all. Who are you using for all your wiring looms. I’m finally biting the bullet and going get a fresh one. Sent from my iPhone using Tapatalk

Hi all I’m looking a for a couple of indicator bulb holders, the US ones for double filament bulbs. Anybody got some kicking around or know where I might find them. Sent from my iPhone using Tapatalk

Afternoon folks I’m wondering if anyone has a photo of bus on a Thaus beam. I’ve got a 4” narrowed one with dropped spindles and on max drop it’s not as low as I expected. Although there is no interior in yet. Just wondered how other people’s sat. I was going to use air shocks for getting in...

As above really, looking for a gauge pod to replace my broken one. Must be in good condition please. Cheers Dan Sent from my iPhone using Tapatalk

As above really. I'm in need of the tinware over the gearbox end to fit a 69 bay. Cheers Dan Sent from my iPhone using Tapatalk

I've ended up with a spare moustache bar, it won't fit my exhaust. Oil bath air filter£40 Front spindles with drums and internals. £60 Lhd beam from 69 bus with csp adjusters. No leaves. Beam is in excellent condition, but welds aren't the prettiest on adjusters, need tidying up. £80 Brand...

Hi Does anyone know where I can source these washers from the front ball joints. They locate the brake pipe clamp. Cheers Sent from my iPad using Tapatalk

Hi everyone First off, what pipe are you all using to run servo to manifold under the van. Heritage list one but it's out of stock. Next up I'm getting ready to put my engine and box in. Any advice to make it easier? Would you fit gearbox then engine or mate the 2 together and put in as 1...

Hi guys I've been assuming that I'm just missing an ignition switch, but I've just realised there must be a lock or housing I need too? This is what I have, but what am I looking for and are they all the same or different depending on year? Cheers Dan Sent from my iPad using Tapatalk

Hi I've got myself a rebuild kit for my servo equipped m/c, but I can't for the life of me get it apart. I've removed the bolt in the top, removed the circlip, washer and rubber seal, is there something else I need to do? It looks like a plastic washer is in there now. Cheers Dan Sent...

I've got a servo now to go on my 69 bus, but as there wasn't one to come off I have no idea where it all goes. The vac hose runs to the manifold with a non return valve, but does it matter where the valve goes and way around (yellow to servo side?). As for the breather, I have no idea where...

Hi I've got some unused parts kicking around. Prices are pus post or collected from Cambridgeshire. Brand new m/c for early bay £60 Air box in excellent condition £40 Sent from my iPad using Tapatalk

Hi Anybody used transporterhaus narrowed beams? What are they like? Also anybody know the prices of the French slammers? Midland are away at the moment and I'm trying to decide which to go with. Any help would be great. Cheers Dan Sent from my iPad using Tapatalk

Hi I've got a csp front disc kit for my 69, but am I correct in thinking I need to modify my master cylinder? Which big do I need to remove? Cheers Dan Sent from my iPad using Tapatalk

Hi guys So piecing together a van I didn't take apart has is proving awkward. I've got the yellow wire that runs down the steering tube from the horn ring. Am I correct in thinking this terminates to earth? The other question is where does the brake fluid reservoir sit, the little round one...

Hi Are the front gearbox mounts available new anywhere? Mines looking a dry and tired, wanted replace it while the box is out. It's the one piece rubber and metal type if that makes sense. Cheers Dan Sent from my iPad using Tapatalk

Early Spindles complete with drums except for the hub nuts. £80 4x new cv gators. £10 Oil bath filter, great condition. £50 New front screen rubber, could use a clean, but perfect condition. £15 Heater bellows. £5 Microbus seat brackets £5 Armrests £10 I also have a set of new boxed front brake...

Hi The loom in the engine bay has been burnt, I need to replace the part going to the rear left tail light and number plate light. It's US 68 bay by the way. Cheers Dan Sent from my iPad using Tapatalk

Hi guys I'm rebuilding my beam with adjusters and new ball joints etc. So I'm looking to get it powder coated. Later on I want add a servo when I fit discs, so figured it's worth getting the mount on now. Does anywhere sell the brackets or anybody have measurements for making one? And then...

Hi guys I've the arms off of my beam at the moment, so I'm going to change the ball joints. I've got a press kit which should work to get the new ones in, but there's nowhere to "seat" the tools to be able to press them out. Any one got any ideas, other than paying someone to do it? Cheers...